PEVALIT was established in 1994 as a trading company working on wholesale and retail sale of locally produced and imported building materials.
STIR 10
Technical Parameters
– Sanding: From 0-1.0 mm.
– Dry mass density: 1500-1900 kg/m³
– Norm: MKC EN ETAG 004, ETA-11/0340
– Work temperatures: +5°C – +30°C.
– Mixing with water: approximately 4 min., with around 26-28% water/25kg.
– Working time in container: Up to 4 hours after mixing.
– Spending: for panel adhesion 4-5 kg/m²; for covering panels with reinforcing mesh 4-5 kg/m²
– Adhesion (separation) from the layers of concrete: After 28 days 0.3 N/mm²
– Adhesion (separation) from the layers of polystyrene: After 28 days 0.08 N/mm²
– Material color: Grey.
– Packaging: 25 kg.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
Aquastop AB 35/G
2C Waterproofing mass
Application
A two-component measure of elastic waterproofing of waterproofing.
Thickness up to 3 mm.
Based on cement (comp. A) and resin (comp. B).
For concrete or porous cement mortar walls, horizontal or vertical.
In outdoor and indoor environments.
For swimming pools, underground structures, water tanks,
terraces, balconies, bathrooms, etc.
High elasticity and good adhesion even on smooth surfaces.
Surfaces must be clean, dry, hard, dust-free and grease-free.
It is applied with a brush or roller, in two or three layers.
For thicker and reinforced layers over 2 mm with glass mesh
the submitted side of the shovel, and as a final layer with
PEVALIT-Aquastop AB30 R with brush or roller.
The interval between layers is 4-6 hours.
Aquastop AB 30R
Technical Parameters
Shelf life: up to 1 hour after mixing.
Operating temperatures: +5°C- +30°C.
Resistant to temperatures: -20°C – +80°C.
Standard: based on EN 14891:2012.
Interval between layers: 4-6 hours.
Exposure to water: After 4 days.
Packaging: 20 + 8 kg. / 5 +2 kg.
Material color: gray.
Shelf life: 12 months in original packaging,in a moisture-free warehouse.
Trake izoluese per tushe
Masat veterrafshuese N Bs
Parametrat teknik
-Dendësia e masës së thatë të papërpunuar: 1830 kg/1m³.
-Fortësia ndaj presionit (pas 28 ditësh): CS IV, ca. 8.0 N/mm².
-Thithja e ujit: W0.
-Temperaturat për punim: +5°C - +30°C
-Koha e punimit në enë: Deri 15 minuta pas përzierjes.
-Trashësia e shtresës: Prej 6 deri 30 mm.
-Përzierja me ujë: Мe rreth 6.3 l/25kg.
-Ngjyra e materialit: Gri
-Paketimi: 25 kg.
-Afati i magazinimit: Në paketim origjinal 12muaj, në depo pa lagështi.
Pevalit Fuga mass F bs
Technical Parameters
– Working time in container: Up to 4 hours after mixing.
– Working time: Up to 20 minutes.
– Work temperatures: +5°C – +30°C.
– Resistant to temperatures: -20°C – +80°C.
– Norm: SG2, based on EN 13888.
– Walking on tiles: After 8 hours.
– Mixing with water: approximately 4 min., with around 0.55 1/2kg.
– Packaging: 2 and 5 kg.
– Material color: According to catalogue.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
Pevalit Fuga mass
Technical Parameters
– Working time in container: Up to 4 hours after mixing.
– Working time: Up to 20 minutes.
– Work temperatures: +5°C – +30°C.
– Resistant to temperatures: -20°C – +80°C.
– Norm: SG2, based on EN 13888.
– Walking on tiles: After 8 hours.
– Mixing with water: approximately 4 min., with around 0.53 l / 2kg.
– Packaging: 2 and 5 kg.
– Material color: According to catalogue.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
P XS
Technical Parameters
– Working time in container: Up to 15 minutes after mixing.
– Working time: Up to 10 minutes.
– Work temperatures: +15°C – +30°C.
– Resistant to temperatures: -35°C – +100°C.
– Norm: C2FT, based on EN 12004.
– Walking on tiles: After 3-6 hours. Measurements are based on temp. around 22°C.
– Walking on tiles with weight: After 6 hours.
– On layers of plaster: PEVALIT-Tiefgrund LF is used.
– Mixing with water: approximately 4 min., with around 24 % water / 25kg.
– Packaging: 25 kg.
– Material color: White.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
P3w S1
Technical Parameters
-Working time in container: Up to 2 hours after mixing.
-Working time: Up to 30 minutes.
-Work temperatures: +5°C – +30°C
– Resistant to temperatures: -30°C – +100°C
– Norm: C2FE – S1, based on EN 12004.
– Walking on tiles: After 4-6 hours. Measurements are based on temp. around 22°C.
– Walking on tiles with weight: After 4 days.
– On layers of plaster: PEVALIT-Tiefgrund LF is used.
– Mixing with water: approximately 4 min., with around 24 % water / 25kg.
– Packaging: 25 kg.
– Material color: White.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
P3 W g&m
Technical Parameters
– Working time in container: Up to 4 hours after mixing.
– Working time: Up to 30 minutes.
– Work temperatures: +5°C – +30°C
– Resistant to temperatures: -30°C – +100°C
– Norm: C2FE, based on EN 12004.
– Walking on tiles: After 24 hours. Measurements are based on temp. around 22°C.
– Walking on tiles with weight: After 4 days.
– On layers of plaster: PEVALIT-Tiefgrund LF is used.
– Mixing with water: approximately 4 min., with around 24 % water / 25kg.
– Packaging: 25 kg.
– Material color: White.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
P3 S1
Technical Parameters
– Working time in container: Up to 4 hours after mixing.
– Working time: Up to 30 minutes.
– Work temperatures: +5°C – +30°C
– Resistant to temperatures: -30°C – +100°C
– Norm: C2FE – S1, based on EN 12004.
– Walking on tiles: After 12-16 hours. Measurements are based on temp. around 22°C.
– Walking on tiles with weight: After 4 days.
– On layers of plaster: PEVALIT-Tiefgrund LF is used.
– Mixing with water: approximately 4 min., with around 24 % water / 25kg.
– Packaging: 25 kg.
– Material color: Grey.
– Best before: In the original packaging 12 months, in a warehouse without moisture.
